We unscrew the two plastic nuts securing the lantern Removing the rear light and replacing bulbs Pulling the lamp out, take it out of the socket We turn the lamp holder counterclockwise and remove the lamp holder from the body Pry on the turn signal with a screwdriver and take it out of the hole in the front fender Removing the side turn signal and replacing the lamp To adjust, insert a long Phillips screwdriver into the hole and adjust the direction of light of the fog lights. To adjust the direction of the fog lamp beam during operation, holes are made in the front bumper Use a hand or a Phillips screwdriver to turn the plastic adjusting screw clockwise to raise the light beam, or counterclockwise to lower the beam. Using the Torx T-20 wrench, unscrew the two headlight mounting screwsĪfter installing the headlight, we adjust the direction of the light beam in the vertical plane.
WHEN INSTALLING MY FOG LIGHTS WHICH IS RIGHT AND LEFT INSTALL
Install the new H11 lamp in reverse order.ĭisconnect the block of wires from the lamp. We squeeze the latch of the block of wires, disconnect the block from the lamp We bend the front part of the fender liner and put it behind the brake disc We unscrew the three self-tapping screws for attaching the fender liner to the front bumper and one self-tapping screw for attaching the fender liner to the fender. Remove the mudguard (article - Removing engine protection, wheel arch liners and Renault Duster mud flaps) Remove the front wheel from the side of the lamp being replaced. We install the car on a viewing ditch or lift To change the direction of the light beam in the horizontal plane, rotate knob 1. To change the direction of the light beam in the vertical plane with a hexagon by 6 (through the hole in the upper cross member of the radiator frame) screw 2. After installing the headlamp unit, adjust the direction of the headlamp beam.
Use a screwdriver to pry on the wire block retainerĭisconnect the block from the headlamp connector Use a screwdriver to squeeze the retainer and remove the headlamp from the body We unscrew the bolt of the lower fastening of the headlight unit With a 10 head, unscrew the bolt of the upper mounting of the headlight unit With a 10 head, unscrew the bolt of the front mounting of the headlight unit We remove the sheath of the cable from the holder on the body of the actuatorĭisconnect the cable end from the headlight range control actuator rod
Remove the protective cover from the headlight range control actuator housing Remove the front bumper (article - Removing and installing bumpers Renault Duster) Install the new W5W lamp in the reverse order. Pulling, remove the lamp holder from the headlight housing. Remove the protective cover of the dipped and side light lamps We attach a block of wires to the new lamp H7 and, having inserted the lamp into the body of the headlamp block, press on the block of wires until the spring clips snap into place. Removing the lamp from the headlight housingĭisconnect the wiring block from the lamp. Pulling the lamp by the block of wires, we disengage the lamp with three spring clips Remove the protective rubber cover of the dipped and side light lamps We take out the lamp from the headlight housing Press on the spring clip of the lamp and disengage it from the hooks of the reflector Remove the protective rubber cover of the high beam lamp
There are two protrusions on the base of the lamp, they are located asymmetrically relative to the lamp axis and must fit into the corresponding grooves of the holder. Install a new PY21W lamp in reverse order The direction indicator lamp holder has two fixing protrusions of different widths, they must fit into the corresponding grooves of the headlamp housing We take out the lamp holder from the headlamp housingĬlick on the lamp, turn it counterclockwise until it stops and remove the lamp from the holder To replace the turn signal lamp, turn the cartridge counterclockwise In the variant version, the cars are equipped with fog lamps installed in the lower part of the bumper.įog lights can be turned on with the steering column switch, only when the outside lights are on.ĭisconnect the negative terminal of the battery The direction indicators installed in the headlights are made without color filters, instead of them lamps with glass of a certain color are used. It is made of plastic, which is more transparent and lighter than a glass shade. The headlamp cover is smooth and does not function as a distribution of light fluxes. The headlights are equipped with transparent glass optics. In the article, we will consider replacing bulbs, headlights, lanterns and car shades
0 kommentar(er)
